Table of Content
...
Ports | Direction | Type | Description |
REF | In | std_logic | Reference clock input Connectivity: semi-dedicated clock inputs, clock trees (low skew network) Note: If REF pin is connected to a PAD, please declare the pad with Turbo mode enabled. |
FBK | In | std_logic | External FeedBack input Connectivity: semi-dedicated clock inputs, clock trees (low skew network) |
VCO | Out | std_logic | VCO output : Fvco = fbk_intdiv * 2**(fbk_div_on - ref_div_on + 1) * clk_ref_freq Connectivity: WFG inputs |
D1…D3 | Out | std_logic | Divided clocks. Fvco frequency divided by 1, 2, 4, 8, 16, 32, 64 or 128 Important note: D1, D2 and D3 outputs are reset while PLL RDY is not asserted. Connectivity: WFG inputs |
OSC | Out | std_logic | Internal 200 MHz oscilator Connectivity :WFG inputs, delay calibration system |
RDY | Out | std_logic | High when PLL is locked Connectivity: RDY inputs of WFGs, fabric… |
...
Ports | Direction | Type | Description |
REF | In | std_logic | Reference clock input Connectivity: semi-dedicated clock inputs, clock trees (low skew network) Note: If REF pin is connected to a PAD, please declare the pad with Turbo mode enabled. |
FBK | In | std_logic | External FeedBack input Connectivity: semi-dedicated clock inputs, clock trees (low skew network) |
R | In | std_logic | Active high Reset input. Must be activated when REF input frequency changes to force a re-locking process of the PLL |
VCO | Out | std_logic | VCO output: - Internal feedback: Fvco = 2 * (fbk_intdiv + 2) * clk_ref_freq / (ref_intdiv + 1) - External feedback: Fvco = (pattern_end + 1) / n_sim_pat * clk_ref_freq / (ref_intdiv + 1) Where n_sim_pat is the number of similar patterns sequence found in pattern_end+1 MSB bits of pattern. |
REFO | Out | std_logic | Output of the REFerence divider. The division factor is set by the generic “ref_intdiv” |
LDFO | Out | std_logic | Output of the FBK_INTDIV divider. The division factor is set by the generic ‘fbk_intdiv” |
DIVP1 | Out | std_logic | This output delivers a divided VCO frequency (by a power of 2). The division factor is set by the generic “clk_divoutp1” |
DIVP2 | Out | std_logic | This output delivers a divided VCO frequency (by a power of 2). The division factor is set by the generic “clk_divoutp2” |
DIVP3 | Out | std_logic | This output delivers a divided VCO frequency (by a power of 2). The division factor is set by the generic “clk_divoutp3o2” |
DIVO1 | Out | std_logic | This output delivers a divided VCO frequency (by an odd factor). The division factor is set by the generic “clk_divouto1” |
DIVO2 | Out | std_logic | This output delivers a divided VCO frequency (by an odd factor). The division factor is set by the generic “clk_divoutp3o2” |
OSC | Out | std_logic | Internal 200 MHz oscilator Connectivity :WFG inputs, delay calibration engine |
PLL_LOCKED | Out | std_logic | High when PLL is locked Connectivity: RDY inputs of WFGs, fabric… |
CAL_LOCKED | Out | std_logic | High when the automatic calibration procedure of the current FPGA quarte area is complete Connectivity: fabric |
...
This generic specifies if the “location” and the “termination” on the instantiated NX_IOB is are done in the instantiation (locked => ‘1’) or in the Nxpython script fine (locked => ‘0’). Example :
...
This generic specifies if the “location” and the “termination” on the instantiated NX_IOB is are done in the instatiation (locked => ‘1’) or in the Nxpython script fine (locked => ‘0’). Example :
...
This generic specifies if the “location” on and the “termination”on the instantiated NX_IOB is are done in the instatiation (locked => ‘1’) or in the Nxpython script fine (locked => ‘0’). Example :
...