...

Operating

...

System

Our software requires a RedHat Enterprise Linux 64-bit distribution such as one of the below operating systems:

• CentOS 7

• CentOS 8

...

...

...

Software

Running Impulse requires Python 3.6 installed on a Linux 64-bit machine.

Download NanoXplore Tools

Follow the steps below to download and unpack NanoXplore tools

1. Visit Support NanoXplore-download and sign-in or register to download:

   • NXLMD => NXLMD-2.12-linux.tar.gz

   • Impulse => nxdesignsuite-version-.tar.gz

   • NxBase2 => NxBase2-2.5.3.1.tar.bz2

2. Save Impulse tools to your ~/Downloads folder or a location of your choice

3. Create a New Folder named NanoXplore in the /opt directory

4. Unpack your downloaded NanoXplore tool directly to /opt/NanoXplore

5. Repeat this process for each NanoXplore tool

...

NX License Daemon

To download and install the NanoXplore License Manager Daemon (NXLMD), please refer to the instructions in the License Daemon guide.

NXbase2 archive extraction

To unpack NxBase2 tool directly once downloaded into /opt/NanoXplore, you must first create a folder named NXbase2- 2.3.1 via the following command:

...

.

...

...

After competing this step, unpack NxBase2 from the ~/Downloads folder (or you download location) using the following command:

 $> sudo tar xjf NxBase2-2.3.1.tar.bz2 -C ./NxBase2-2.3.1

Installation

Below the main steps to setup and install each NanoXplore tool:

1. Update ~/.bashrc file for each NanoXplore tool

2. Verify that the ~/.bashrc update has been taken into account using the below command:

   Code Block
   $> source ~/.bashrc”

3. Restart your machine

Install Impulse

Follow the steps below to install Impulse:

1. Before install Impulse, check that Python 3.6 is installed with below command:

   Code Block
   $> which python3

   If Pyhton3 is installed you will see the following line:

   Code Block
   $> /usr/bin/python3

2. If Python3 is not installed, run the following command:

   Code Block
   $> sudo yum install python3

3. To install Impulse, update ~/.bashrc file with below instruction:

   Code Block
   export PATH=/opt/NanoXplore/impulse-/bin:$PATH

   Check that ~/.bashrc updating has been taken into account with below command:

   Code Block
   $> source ~/.bashrc”

4. Check that Impulse is installed with below commands:

   Code Block
   $> which impulse

   The result of this command must be the following

   Code Block
   $> /opt/NanoXplore/impulse-version/bin/impulse

5. Check that Impulse works correctly with Impulse is working as expected by running the following command:

   Code Block
   $> impulse --version

   The result of this command must be the following

   Image Removed

NxBase2

...

The result should display as follows:

...

How to Install NxBase2

1. Navigate to the NanoXplore tools directory:

   Code Block
   $> cd /opt/NanoXplore

2. Create a new folder named NxBase2-2.5.3:

   Code Block
   $> sudo mkdir NxBase2-2.5.3

3. Extract the NxBase2 TAR archive to the /opt/NanoXplore folder:

   Code Block
   $> sudo tar xvf NxBase2-2.5.3.tar.bz2 -C ./NxBase2-2.5.3

Make NxBase2 Available

After you install NxBase2, you should do the following to enable direct access to nxbase2_cli from any directory:

1. Update the ~/.bashrc file using the following instruction:

   Code Block
   export PATH=/opt/NanoXplore/NxBase2-2.5.3.1/install_cst/centos6other_os/nxbase2_cli:$PATH

2. Check that NxBase2 has been installed and works correctly with below commands:

   Code Block
   $> which nxbase2_cli $> nxbase2_cli --version

Install ANGIE

1. Plug your ANGIE device to your system using the USB cable provided

2. Check the board is detected using the below command:

   Code Block
   $> lsusb

...

The result should look like the screenshot below:

...

Configure ANGIE Access Rights

To grant ANGIE access rights to the User:

1. Create a file named “9999-nanoxbase.rules”rules

2. Add the following lines to “9999-nanoxbase.rules”rules:

   Code Block

   ACTION=="add", SUBSYSTEM=="usb", ATTRS{idVendor}=="8613", ATTRS{idProduct}=="584e", MODE="660", GROUP="plugdev" ACTION=="add", SUBSYSTEM=="usb", ATTRS{idVendor}=="584e", ATTRS{idProduct}=="424e", MODE="660", GROUP="plugdev" ACTION=="add", SUBSYSTEM=="usb", ATTRS{idVendor}=="584e", ATTRS{idProduct}=="4242", MODE="660", GROUP="plugdev" ACTION=="add", SUBSYSTEM=="usb", ATTRS{idVendor}=="584e", ATTRS{idProduct}=="4342", MODE="660", GROUP="plugdev" ACTION=="add", SUBSYSTEM=="usb", ATTRS{idVendor}=="584e", ATTRS{idProduct}=="4a55", MODE="660", GROUP="plugdev" ACTION=="add", SUBSYSTEM=="usb", ATTRS{idVendor}=="58c0", ATTRS{idProduct}=="804e", MODE="660", GROUP="plugdev"

3. Copy this the 99-nanoxbase.rules file to /etc/udev/rules.d directory using the command below:

   Code Block
   $> sudo cp 99-nanoxbase.rules /etc/udev/rules.d

4. Reload the udev rules with the following command:

   Code Block
   $> sudo udevadm control –reload-rules

5. Restart machine after above command

6. Check that the board is detected using the below command:

   Code Block
   $> lsusb

   Image Removed

...

1. Disconnect and reconnect the USB plug from your ANGIE adapter