Copyright

All the contents of this document are protected by the copyright law. They may not be disclosed to third parties or copied or duplicated in any form without consent of NanoXplore.

Introduction

Aim of document

This document is intended to guide users on NXmap software best practice.

...

For any kind of help, please contact NanoXplore support team at support@nanoxplore.com.

Content

All recommendations are divided in several categories depending on product development phase.

They are based mainly on NXpython methods but some of them can be applied in the GUI.

Design

NanoXplore primitive instantiation

All NanoXplore primitives are listed in nxLibrary-<variant_name>.vhdp available in the release archive. A documentation is also available in order to get information about all generics and io in Impulse 23.1 Library guide MEDIUM/LARGE .

Clock management

NanoXplore FPGAs contain a low-skew network in order to spread signal with high fanout like clock, reset, load signals.

...

1. Use a pad directly connected to the closest CKG (these pads are suffixed by _CLK). Either the user instantiates a PLL or a WFG in the design or the tool instantiates automatically a WFG in bypass mode.

2. 1. MEDIUM/LARGE: Use a common pad or internal logic and use a buffer NX_BD in global_lowskew mode.

   2. ULTRA: Use a common pad or internal logic and use a NX_GCK_U in Common to System Converter CSC mode.

Please have a look at Impulse 23.1 Training Package : Application Note Design/LowskewManagement project.

...

• Clock Gating:

  • MEDIUM/LARGE: Use a NX_CKS to gate a clock system signals with a command common signal.

  • ULTRA: Use a NX_GCK_U in Clock Switch CKS mode to gate a clock system signals with a command common signal.

• Clock MUX:

  • ULTRA: Use a NX_GCK_U in Clock MUX MUX mode to switch between 2 clock system signals with a command common signal.

Please have a look at Impulse 23.1 Training Package : Application Note Component/ClockSwitch project.

Reset management

Like clocks, reset are generally spread to the whole design through the low-skew network because of high fanout too.

Reset can be asynchronous or synchronous as registers of NanoXplore FPGAs are compliant with both.

Global signals management

There are some signals with high fan out can be mapped into low-skew network and introduced some important delays. It could be the problem with synchronous signals load, set, reset, …

...

p.rejectLowskew('inst1|reset_sync')

Memory initialization

There are several ways to initialize a memory (attribute, generic, python method).

It is recommended to rather use python method addMemoryInitialization described in Impulse 23.1 NxPython Specification as it is compliant with inferred and instantiated memories.

Please have a look at Impulse 23.1 Training Package : Application Note Init/Ram project.

Memory Inference

In order to infer a memory instead of instantiating a NanoXplore primitive (advantage is the user can choose with the same RTL code to map this memory in RF, RAM, RAM_ECC, … thanks to NXpython constraints), it is recommended to follow TrainingPackage Design/MemInfer examples providing inference for ROM, SRAM, DPRAM with and without ECC.

Please have a look at Impulse 23.1 Training Package : Application Note Design/MemInfer project.

Hierarchy

It is recommended to divide the design in well sized modules depending on the function they are responsible for.

It will be very helpful to constrain the design by module then.

Logic depth

It is highly recommended to avoid large logic depth between registers as it will limit the maximum frequency of the design.

In addition, when a LUT is used, the DFF from the same Functionnal Element will be used either as a register or a buffer so adding pipeline in the design won’t consume any additional instance.

Project creation

NXmap is based on Python scripts that is to say a project is a class and all options and constraints are methods associated to this class.

...

• Set options before any progress.

• Set IO pads locations and parameters before any progress.

• Save your project after each progress step.

• Separate your project in categories (setup,synthesis, placing, routing, sta) and set your constraints at the right place.

Project check

Once the project is launched, it is necessary to check logs and reports in order to be sure there is not any issue leading to errors, undesired optimizations, …

Logs and report files analysis

Errors and warnings

First of all, check the project is successful until the required progress step.

...

Even though the project is successful, it is advised to parse these files.

Complexity

After errors and warnings are solved or understood, check hierarchy.rpt and progress.rpt in order to check the number of instances is relevant with the estimation.

In order to get complexity module by module without confining it in a region, it is possible to use addModule method described in Impulse 23.1 NxPython Specification.

Refer to #Floor_planning_Complexity for more details.

IO Location

Check in progress.rpt none IO has been automatically placed by the design. It is marked with an exclamation sign.

Common Errors

There are typical types of errors :

...

• If modules are constrained with constrainModule method, increase area size

• Change the Seed used for P&R

• Change the following options: CongestionEffort, DensityEffort, RoutingEffort

STA

Once the project is mature enough, Static Timing Analysis can be done in order to check how fast the design can operates.

...

Clock creation

The input clock frequencies and other parameters must be informed to NXmap for STA.

Please refer to createClock and createGeneratedClock described in Impulse 23.1 NxPython Specification .

If a PLL is used, PLL output clock frequencies are automatically computed by the software.

Special path and clock domains relationship

Declare all false paths and multi cycle paths in order to not take into account some paths between registers in some particular cases.

Please refer to addFalsePath and addMultiCyclePath in Impulse 23.1 NxPython Specification .

Clock groups can be created if clock domains are completely unrelated.

Timing files analysis

When launching the STA tool, the following files are created :

...

Use the first 3 timing files in order to get an overview of the project and other ones to analyze paths.

Optimization

Mapping

Operator

Operators are divided in 3 categories :

...

It is possible to map this operators in LUT, Carry or DSP thanks to addMappingDirective method described in Impulse 23.1 NxPython Specification .

By default, adders are mapped into Carry and Multipliers in DSP. But it can sometimes be interesting to change default mapping directives.

Check #Mapping_Directive_Operator for information about constraint setting.

Memory

Memories can be mapped into logic elements (LUT/DFF), register files (RF), Memory Blocks (RAM) or Memory Blocks protected by EDAC correction thanks to addMappingDirective method described in Impulse 23.1 NxPython Specification .

By default, small memories (equal or less than 64x16) will be mapped into RF and bigger mapped into RAM. But it can sometimes be interesting to change default mapping directives.

...

Check #Mapping_Directive_Memory for information about constraint setting.

Placing

In order to improve the maximum clock frequency for each clock domain, it is advised to follow the following steps:

• Define a floor plan for the design depending on module relationships and pinout.

• Apply the floor plan to your NXmap project using confineModule described in Impulse 23.1 NxPython Specification . Check #Floor_planning_Constrain_module for information about constraint setting.

• If needed, repeat this process going deeper and deeper in the design hierarchy.

• For last most critical paths, use constrainPath described in Impulse 23.1 NxPython Specification in order to create a region with only a few elements contained into the specified path. Check #Floor_planning_Constrain_path_between_registers for information about constraint setting.

It can also have a very positive impact to create unitary projects and reuse the routed projects as a blackbox in your final top project using addBlackBox described in Impulse 23.1 NxPython Specification .

It is also possible to place manually instances in a specified spot thanks to the following NXpython methods all described in Impulse 23.1 NxPython Specification :

• addPLLLocation for PLL instance in a CKG. Check #Instance_placing_Ring_placing for information about constraint setting.

• addWFGLocation for WFG instance in a CKG and a WFG spot. Check #Instance_placing_Ring_placing for information about constraint setting.

• addRAMLocation for RAM instance in a CGB. Check #Instance_placing_Ram_placing for information about constraint setting.

• addDSPLocation for DSP instance in a CGB and a DSP spot. Check #Instance_placing_Dsp_placing for information about constraint setting.

• setSite for LUT/DFF/CY in a TILE. Check #Instance_placing_Tile_placing for information about constraint setting.

Anchor
Design_complexity Design_complexity

Design Complexity

The logic depth of a design must be controlled. the method reportDesignComplexity and reportHierarchyComplexity are very helpful to have an overview.

Please have a look at Impulse 23.1 NxPython Specification reportDesignComplexity and reportHierarchyComplexity methods.

Anchor
Complexity Complexity

Complexity

In order to get complexity for each module of the design, check the detailed hierarchy of the design.

...

08:50:49:info     |     --------------------------------------------
08:50:49:info     |     - Detailed Hierarchy Statistics            -
08:50:49:info     |     --------------------------------------------
08:50:49:info     |     ~                   hierarchical
08:50:49:info     |                         Resources:
08:50:49:info     |                           NX_LUT : 13
08:50:49:info     |                           NX_DFF : 73
08:50:49:info     |                           NX_IOB : 51
08:50:49:info     |                           NX_BFR : 99
08:50:49:info     |                           NX_WFG : 3
08:50:49:info     |     ~                   |-> row_col_pipe(X212B9C19) [ GEN_HIER0 ]
08:50:49:info     |                         |-> Resources:
08:50:49:info     |                         |->   NX_LUT : 3
08:50:49:info     |                         |->   NX_DFF : 23
08:50:49:info     |     GEN_HIER0_ROW-0     |   |-> timing_pipe(X2A98C8C6) [ GEN_HIER0|GEN_ROW[0].ROW_PIPE ]
08:50:49:info     |                         |   |-> Resources:
08:50:49:info     |                         |   |->   NX_DFF : 5
08:50:49:info     |     ~                   |   |-> timing_pipe(X2A98C8C6) [ GEN_HIER0|GEN_ROW[1].ROW_PIPE ]
08:50:49:info     |                         |   |-> Resources:
08:50:49:info     |                         |   |->   NX_DFF : 5

How to use NXpython constrains methods

Mapping directive

Anchor
Mapping_directive_Operator Mapping_directive_Operator

Operator

In order to map an operator into LUT, CY or DSP, follow the following steps:

• Launch your design for the first time without constraint.

• Grab the operator model or instance in operators.rpt report. For instance, “ | Operator 'add_3u_3u' | : add_L25 (line 25 in …”, model name is “add_3u_3u” and instance name is “add_L25”.

• Add the constraint specifying instance to map the operator, for instance “ p.addMappingDirective('getModels(add_3u_3u)','ADD','DSP')” or p.addMappingDirective('getInstances(add_L25)','ADD','DSP')”, and relaunch the project.

• Check in operators.rpt report the constraint matched with the desired instance.

Please have a look at Impulse 23.1 Training Package : Application Note MappingDirective/Operator project.

Anchor
Mapping_directive_Memory Mapping_directive_Memory

Memory

In order to map an operator into FE, RF, RAM or RAM_ECC, follow the following steps:

• Launch your design for the first time without constraint.

• Grab the memory model in memories.rpt report. For instance, “ | Ram 'RAM_s_mem' Analysis:”, model name is “RAM_s_mem”.

• Add the constraint specifying instance to map the operator, for instance “ p.addMappingDirective('getModels(RAM_s_mem)','RAM','RAM_ECC')”, and relaunch the project.

• Check in memories.rpt report the constraint matched with the desired instance.

Please have a look at Impulse 23.1 Training Package : Application Note MappingDirective/Memory project.

Instance placing

Anchor
Instance_placing_Dsp_placing Instance_placing_Dsp_placing

DSP placing

In order to place manually an inferred DSP in a CGB spot, follow the following steps:

...

Please have a look at Impulse 23.1 Training Package : Application Note PlacingConstraint/DspLocation project.

Anchor
Instance_placing_Ram_placing Instance_placing_Ram_placing

RAM placing

In order to place manually an inferred RAM in a CGB spot, follow the following steps:

...

Please have a look at Impulse 23.1 Training Package : Application Note PlacingConstraint/RamLocation project.

Anchor
Instance_placing_Ring_placing Instance_placing_Ring_placing

Ring placing

In order to place manually an automatically created WFG in a CKG spot, follow the following steps:

...

Please have a look at Impulse 23.1 Training Package : Application Note PlacingConstraint/RingLocation project.

Anchor
Instance_placing_Tile_placing Instance_placing_Tile_placing

Tile placing

In order to place manually an inferred TILE instance like DFF, LUT or CY, follow the following steps:

• Launch your design for the first time without constraint.

• Grab the register name in RegisterSummary.rpt report or in timing files. For instance, i_cpt_0|s_cpt_out_reg[5]”.

• Add the constraint specifying TILE spot (TILE coordinates), for instance “p.setSite('i_cpt_0|s_cpt_out_reg[0]','TILE[2x2]'”, and relaunch the project.

• Check in preplaced.rpt report the constraint matched with the desired instance.

Please have a look at Impulse 23.1 Training Package : Application Note PlacingConstraint/Site project.

Floor planning

Anchor
Floor_planning_Constrain_module Floor_planning_Constrain_module

Constrain Module

In order to confine a module (component of the design hierarchy) in a region containing TILE, CGB and MESH, follow the following steps:

• Launch your design for the first time without constraint.

• Grab the module name in hierarchy.rpt report. For instance, “| ~ |-> row_col_pipe(X212B9C19) [ GEN_HIER0 ]”, name is “|-> row_col_pipe(X212B9C19) [ GEN_HIER0 ]”.

• Add the constraint specifying area coordinates, for instance “p.constrainModule('|-> row_col_pipe(X212B9C19) [ GEN_HIER0 ]','GEN_HIER0_ROW_M','Soft',9,6,2,3,'GEN_HIER0_ROW_R',False)”, and relaunch the project.

• Check in hierarchy.rpt report the constraint matched with the desired instance.

Please have a look at Impulse 23.1 Training Package : Application Note PlacingConstraint/Region project.

Anchor
Floor_planning_Constrain_path_between_register Floor_planning_Constrain_path_between_register

Constrain path between registers

In order to confine all instances in a path between 2 registers in a region containing TILE, CGB and MESH, follow the following steps:

• Launch your design for the first time without constraint.

• Grab the source and target register in DOMAIN_<clk1>_to_<clk2>_<progress_step>_<conditions>.timing. For instance, “module0|submodule0|pipe_reg[0].CK” and “module0|submodule0|pipe_reg[1].CK” , names are “module0|submodule0|pipe_reg[0]” and “module0|submodule0|pipe_reg[1]”.

• Add the constraint specifying area coordinates, for instance “p.constrainPath('|-> row_col_pipe(X212B9C19) [ GEN_HIER0 ]','PIPE_REG_M','Soft',9,6,2,3,'PIPE_REG_R',False)”, and relaunch the project.

• Check in hierarchy.rpt report the constraint matched with the desired instance.

Please have a look at Impulse 23.1 Training Package : Application Note PlacingConstraint/ConstrainPath project.

Anchor
Floor_planning_Preplace_ip Floor_planning_Preplace_ip

Preplace IP

In order to preplace a macro IP of a global design in order to reach design specifications (delays, maximum frequencies, …) in an area of the chip before integrating it in the global design, follow the following steps:

• Define the macro IP as the top cell.

• Define a minimum aperture and all needed constraints as it was a global project to reach specifications. Save the project file after routed steps.

• Run the project until Placing 3/5 step and use saveIP method to save the preplaced IP.

• Do not declare the macro IP entity file in the global project. Instead, add the macro IP as a blackbox, specifying coordinates of the top left corner of the macro IP aperture in the global project, for instance “p.addBlackBox('switch_counter',IP','../switch_counter_preplaced.json','g_inst.i_switch_counter_0:1x8')”.

• Check in log the constraint matched.

Please have a look at Impulse 23.1 Training Package : Application Note PlacingConstraint/Preplace project.

STA constraints

Anchor
Sta_constraints_Clock_declaration Sta_constraints_Clock_declaration

Clock declaration

In order to declare a clock in your project in order to get required frequencies in logs, follow the following steps:

...

Please have a look at Impulse 23.1 Training Package : Application Note StaConstraint/GeneratedClock project.

Anchor
Sta_constraints_Generated_clock_declaration Sta_constraints_Generated_clock_declaration

Generated clock declaration

In order to declare a clock in your project in order to get required frequencies in logs, follow the following steps:

• Grab the clock name getting the hierarchy path to the generated clock.

  • Add the constraint specifying clock parameters, for instance “p.createGeneratedClock(getClock('clk_main'),getRegisterClock('i_clock_0|counter_reg[0]'), 'clk_fabric',{'DivideBy': 2})”.

• Check timing files are created for this new clock domain.

Please have a look at Impulse 23.1 Training Package : Application Note StaConstraint/GeneratedClock project.

Anchor
Sta_constraints_Constrain_path_between_registers Sta_constraints_Constrain_path_between_registers

Constrain path between registers

In order to declare a path between 2 registers as a false path, multi-cycle path, min or max delay path, follow the following steps:

• Launch your design for the first time without constraint.

• Grab the source and target register in DOMAIN_<clk1>_to_<clk2>_<progress_step>_<conditions>.timing. For instance, “module0|submodule0|pipe_reg[0].CK” and “module0|submodule0|pipe_reg[1].CK” , names are “module0|submodule0|pipe_reg[0]” and “module0|submodule0|pipe_reg[1]”.

• Add the constraint specifying area coordinates, for instance “p.addFalsePath('getRegisters(module0|submodule0|pipe_reg[0])','getRegisters(module0|submodule0|pipe_reg[0])')”, and relaunch the project.

• Check in DOMAIN_<clk1>_to_<clk2>_<progress_step>_<conditions>.timingt report the path no longer appears.

Please have a look at Impulse 23.1 Training Package : Application Note StaConstraint/FalsePath project.

How to improve STA results

STA tool

It is recommended to launch the STA tool after Placing 1/5 step named “Preparing”. It allows to witness the number of logic elements crossed and check if it is possible to reach performances when the margin in the most optimistic scenario is high enough.

ClockCreation

Before launching STA tool, all constraints must be defined.

...

• createClock for clock coming from a port. Refer to #Sta_constraints_Clock_creation.

• createGeneratedClock if a clock is generated inside the fabric. Refer to #Sta_constraints_Generated_clock_creation.

• addFalsePath in order to remove paths to ignore. Refer to #Sta_constraints_Path_between_registers.

TimingDriven

TimingDriven option can be set with the following constraint:

...

Floor planning

In order to give indications to the tool, the user can set up a floor-planning and pass it through the tool working directly on the whole design or working with unitary runs before integrating in the top design as specified in #Floor_planning_Preplace_ip.

...

Logic depth reducing

The highest the required frequency is, the lowest the number of combinatorial elements between 2 registers must be.

...